A Site dedicated Vintage technology
  1. Home
  2. /
  3. Vintage Cameras
  4. /
  5. Praktica Super TL slow speed escapement clean and...

Praktica Super TL slow speed escapement clean and lubricate.

A few days ago I received a Praktica Super TL 35 mm camera which had a problem with the slow speeds. In this post I'm going to describe the procedure I used to remove the Praktica Super TL slow speed escapement, clean it and get it working again.

The first part of the operation is to reveal the slow speed escapement which is situated in the bottom compartment, so the bottom cover needs to come off. To do this, you need to peel the cover material off the steel bottom plate, which I found was relatively easy to do. I just picked at one edge and found it started to come off without any damage at all. With this off, I found three screws which were easy to remove, but the bottom cover still wouldn't budge because the battery cover needed to be removed.

Unfortunately, one of the reasons the camera was cheap was because the battery compartment was seized and couldn't be moved! I had to resort to holding the cover with a pair of pliers in order to free it, but fortunately I didn't cause any really bad damage.

With the battery cover off, I could remove the bottom of the camera and see the slow speed escapement, but it wasn't immediately apparent how I could remove it.  Since I couldn't work out how to get it out, I decided the best approach would be to take detailed pictures of everything I removed, so I could easily reassemble. If you have a similar camera, I hope the pictures above will help you to carry out the same operation.

Following this approach I removed a spring and a lever which I didn't need to, but they were quite easy to put back on the escapement once it was finally removed. During this procedure, however, I discovered that a small spring at the bottom of a post was not actually connected to anything, so I think that could be one part of my problems with the camera. There is an obvious connection point for it, so when I reassemble the camera I will connect it back up.

Praktica Super TL slow speed clean and lubricate - I did need to remove this screw
I did need to remove this screw

As it turned out, to remove the escapement from the bottom of the camera I only needed to remove a screw in the bottom right-hand side (which is in the picture labelled 'I did need to remove this screw'), the post with two springs attached and the screw which is situated under the speed selector (which means the speed selector components all need to be removed).

Once I had the escapement out of the camera, cleaning it was relatively simple. I adopted the same approach I'd used with my Agfa Ambi Silette self-timer - put it in a small container and flood it with IPA to remove all the old lubricant and grease. Once this was done, I lubricated the points where the bearing turn in the top and bottom plate of the escapement, and it seemed to run nicely.

The next part of this post will deal with the reassembly of the escapement into the camera body.

How useful was this article?

Click on a star to rate it!

Average rating 4.8 / 5. Vote count: 6

No votes so far! Be the first to rate this article.

As you found this post useful...

Please consider sharing to social media

We are sorry that this post was not useful for you!

Let us improve this post!

Tell us how we can improve this post?

One comment on “Praktica Super TL slow speed escapement clean and lubricate.”

  1. Nice, bookmarked this for future reference. I realise that this is almost a decade ago but did you get a look at what is behind the slow speed escapement once you got it out? I have a super tl where the actuator for stopping the lens down don’t move forward enough when pressing the metering button (works fine when pressing the shutter button though). I figure that should be “behind” the slow speed escapement but I don’t know how accessible it would be.

Leave a Reply

Newsletter



    Area of interest

    Cameras & Lenses
    Photos & Films
    Projectors
    Radios & Tape Recorders

    I accept the privacy statement

    You can edit your preferences and unsubscribe at any time after subscribing. Privacy Statement

    All content @SimonHawketts 2024
    linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram
    ×